Mendeteksi keruskan komputer dari bunyi beep  

Membahas semua hal yang berhubungan dengan hardware komputer

Mendeteksi keruskan komputer dari bunyi beep

Postoleh ceka »

Beep Error Kode
Setiap komputer mempunyai kode beep berbeda-beda tergantung dengan biosnya

AMI BIOS
Beep Kode Deskripsi
1x pendek DRAM refresh failure

2x pendek Parity circuit failure

3x pendek Base 64K RAM failure

4x pendek System timer failure

5x pendek Process failure

6x pendek Keyboard controller Gate A20 error

7x pendek Virtual mode exception error

8x pendek Display memory Read/Write test failure

9x pendek ROM BIOS checksum failure

10x pendek CMOS shutdown Read/Write error

11x pendek Cache Memory error

1x panjang, 3x pendek Conventional/Extended memory failure

1x panjang, 8x pendek Display/Retrace test failed


AWARD BIOS
Beep Kode Deskripsi
1 panjang, 2 pendek Indicates a video error has occurred and the BIOS cannot initialize the video screen to display any additional information

Beep lainnya RAM problem.


IBM BIOS
Beep Kode Deskripsi
Tidak ada beep No Power, Loose Card, or Short.

1x pendek Normal POST, computer is ok.
2x pendek POST error, review screen for error code.
Continuous Beep No Power, Loose Card, or Short.

Repeating Short Beep No Power, Loose Card, or Short.

One Long and one Short Beep Motherboard issue.

One Long and Two Short Beeps Video (Mono/CGA Display Circuitry) issue.

One Long and Three Short Beeps. Video (EGA) Display Circuitry.

Three Long Beeps Keyboard / Keyboard card error.

One Beep, Blank or Incorrect Display Video Display Circuitry.


Macintosh startup tones
Tones Error
Error Tone. (two sets of different tones) Problem with logic board or SCSI bus.
Startup tone, drive spins, no video Problem with video controller.
Powers on, no tone. Logic board problem.
High Tone, four higher tones. Problem with SIMM.


Phoenix BIOS
Phoenix BIOS Q3.07 atau 4.X
Beep Kode Deskripsi
1-1-1-3 Verify Real Mode.
1-1-2-1 Get CPU type.
1-1-2-3 Initialize system hardware.
1-1-3-1 Initialize chipset registers with initial POST values.
1-1-3-2 Set in POST flag.
1-1-3-3 Initialize CPU registers.
1-1-4-1 Initialize cache to initial POST values.
1-1-4-3 Initialize I/O.
1-2-1-1 Initialize Power Management.
1-2-1-2 Load alternate registers with initial POST values.
1-2-1-3 Jump to UserPatch0.
1-2-2-1 Initialize keyboard controller.
1-2-2-3 BIOS ROM checksum.
1-2-3-1 8254 timer initialization.
1-2-3-3 8237 DMA controller initialization.
1-2-4-1 Reset Programmable Interrupt Controller.
1-3-1-1 Test DRAM refresh.
1-3-1-3 Test 8742 Keyboard Controller.
1-3-2-1 Set ES segment to register to 4 GB.
1-3-3-1 28 Autosize DRAM.
1-3-3-3 Clear 512K base RAM.
1-3-4-1 Test 512 base address lines.
1-3-4-3 Test 512K base memory.
1-4-1-3 Test CPU bus-clock frequency.
1-4-2-4 Reinitialize the chipset.
1-4-3-1 Shadow system BIOS ROM.
1-4-3-2 Reinitialize the cache.
1-4-3-3 Autosize cache.
1-4-4-1 Configure advanced chipset registers.
1-4-4-2 Load alternate registers with CMOS values.
2-1-1-1 Set Initial CPU speed.
2-1-1-3 Initialize interrupt vectors.
2-1-2-1 Initialize BIOS interrupts.
2-1-2-3 Check ROM copyright notice.
2-1-2-4 Initialize manager for PCI Options ROMs.
2-1-3-1 Check video configuration against CMOS.
2-1-3-2 Initialize PCI bus and devices.
2-1-3-3 Initialize all video adapters in system.
2-1-4-1 Shadow video BIOS ROM.
2-1-4-3 Display copyright notice.
2-2-1-1 Display CPU type and speed.
2-2-1-3 Test keyboard.
2-2-2-1 Set key click if enabled.
2-2-2-3 56 Enable keyboard.
2-2-3-1 Test for unexpected interrupts.
2-2-3-3 Display prompt Press F2 to enter SETUP.
2-2-4-1 Test RAM between 512 and 640k.
2-3-1-1 Test expanded memory.
2-3-1-3 Test extended memory address lines.
2-3-2-1 Jump to UserPatch1.
2-3-2-3 Configure advanced cache registers.
2-3-3-1 Enable external and CPU caches.
2-3-3-3 Display external cache size.
2-3-4-1 Display shadow message.
2-3-4-3 Display non-disposable segments.
2-4-1-1 Display error messages.
2-4-1-3 Check for configuration errors.
2-4-2-1 Test real-time clock.
2-4-2-3 Check for keyboard errors
2-4-4-1 Set up hardware interrupts vectors.
2-4-4-3 Test coprocessor if present.
3-1-1-1 Disable onboard I/O ports.
3-1-1-3 Detect and install external RS232 ports.
3-1-2-1 Detect and install external parallel ports.
3-1-2-3 Re-initialize onboard I/O ports.
3-1-3-1 Initialize BIOS Data Area.
3-1-3-3 Initialize Extended BIOS Data Area.
3-1-4-1 Initialize floppy controller.
3-2-1-1 Initialize hard-disk controller.
3-2-1-2 Initialize local-bus hard-disk controller.
3-2-1-3 Jump to UserPatch2.
3-2-2-1 Disable A20 address line.
3-2-2-3 Clear huge ES segment register.
3-2-3-1 Search for option ROMs.
3-2-3-3 Shadow option ROMs.
3-2-4-1 Set up Power Management.
3-2-4-3 Enable hardware interrupts.
3-3-1-1 Set time of day.
3-3-1-3 Check key lock.
3-3-3-1 Erase F2 prompt.
3-3-3-3 Scan for F2 key stroke.
3-3-4-1 Enter SETUP.
3-3-4-3 Clear in-POST flag.
3-4-1-1 Check for errors
3-4-1-3 POST done--prepare to boot operating system.
3-4-2-1 One beep.
3-4-2-3 Check password (optional).
3-4-3-1 Clear global descriptor table.
3-4-4-1 Clear parity checkers.
3-4-4-3 Clear screen (optional).
3-4-4-4 Check virus and backup reminders.
4-1-1-1 Try to boot with INT 19.
4-2-1-1 Interrupt handler error.
4-2-1-3 Unknown interrupt error.
4-2-2-1 Pending interrupt error.
4-2-2-3 Initialize option ROM error.
4-2-3-1 Shutdown error.
4-2-3-3 Extended Block Move.
4-2-4-1 Shutdown 10 error.
4-3-1-3 Initialize the chipset.
4-3-1-4 Initialize refresh counter.
4-3-2-1 Check for Forced Flash.
4-3-2-2 Check HW status of ROM.
4-3-2-3 BIOS ROM is OK.
4-3-2-4 Do a complete RAM test.
4-3-3-1 Do OEM initialization.
4-3-3-2 Initialize interrupt controller.
4-3-3-3 Read in bootstrap code.
4-3-3-4 Initialize all vectors.
4-3-4-1 Boot the Flash program.
4-3-4-2 Initialize the boot device.
4-3-4-3 Boot code was read OK.
ceka
 
Post: 29
Bergabung: Kam Mar 15, 2012 8:19 am

Re: Mendeteksi keruskan komputer dari bunyi beep

Postoleh kang boim »

Salam Kenal boss ni saya baru masuk di forum ini , makasih artikelnya sangat membantu sekali activitas saya sehari hari,
itu kode bisa segala merk ya boss maksudnya tidak merk yang boos tulis itu ya.
makasih bantuannya
kang boim
 
Post: 2
Bergabung: Jum Feb 01, 2013 7:28 pm

Re: Mendeteksi keruskan komputer dari bunyi beep

Postoleh ceka »

Yang Penting Bios nya Bro.. Merk apa aja Oke..
ceka
 
Post: 29
Bergabung: Kam Mar 15, 2012 8:19 am

Re: Mendeteksi keruskan komputer dari bunyi beep

Postoleh o'wix »

mantap boss,, salam kenal..
o'wix
 
Post: 1
Bergabung: Rab Mei 29, 2013 1:35 am

Re: Mendeteksi keruskan komputer dari bunyi beep

Postoleh kenichiwibowo »

biasanya itu bisa jadi power supply nya rusak. harus ganti. untung ane pake dell gak pernah alamin yah
kenichiwibowo
 
Post: 4
Bergabung: Jum Mar 07, 2014 1:49 pm


Kembali ke Hardware

Siapa yang online

Pengguna yang berada di forum ini: Tidak ada pengguna yang terdaftar dan 1 tamu

cron